Gentoo driver sd needs updating

Hi, I have much trouble to get sata working with an Intel 82801I (ICH9 Family) interface from a Compaq dc5800.

The minimal CD 2008.0 uses the ata driver and not sata so harddisks are registered as /dev/hda.

This forum is for any topics relating to Linux and either traditional laptops or netbooks (such as the Asus EEE PC, Everex Cloud Book or MSI Wind). Note that registered members see fewer ads, and Content Link is completely disabled once you log in. Visit the following links: Site Howto | Site FAQ | Sitemap | Register Now If you have any problems with the registration process or your account login, please contact us. This guide was created as an overview of the Linux Operating System, geared toward new users as an exploration tour and getting started guide, with exercises at the end of each chapter.

Please visit this page to clear all LQ-related cookies.

I have a Dell Inspiron 1501 which is currently running the 2.6.18-gentoo-r6 kernel. EST 2006) megasas: .01 Thu July 24 PST 2008 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 EST 2006) megaraid: 2.20.4.9 (Release Date: Sun Jul 16 EST 2006) megasas: .01 Sun May 14 PDT 2006 libata version 2.00 loaded.

The hard drive controller is an ATI SB600 Non-Raid-5 SATA. ahci 00.0: version 2.0 GSI 18 sharing vector 0x C1 and IRQ 18 ACPI: PCI Interrupt 00.0[A] - IRQ 193 ahci 00.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode ahci 00.0: flags: 64bit ncq ilck pm led clo pmp pio slum part ata1: SATA max UDMA/133 cmd 0x FFFFC20000024100 ctl 0x0 bmdma 0x0 irq 193 ata2: SATA max UDMA/133 cmd 0x FFFFC20000024180 ctl 0x0 bmdma 0x0 irq 193 ata3: SATA max UDMA/133 cmd 0x FFFFC20000024200 ctl 0x0 bmdma 0x0 irq 193 ata4: SATA max UDMA/133 cmd 0x FFFFC20000024280 ctl 0x0 bmdma 0x0 irq 193 scsi0 : ahci ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7, max UDMA/100, 117210240 sectors: LBA48 NCQ (depth 31/32) ata1.00: ata1: dev 0 multi count 16 ata1.00: configured for UDMA/100 scsi1 : ahci ata2: SATA link down (SStatus 0 SControl 300) scsi2 : ahci ata3: SATA link down (SStatus 0 SControl 300) scsi3 : ahci ata4: SATA link down (SStatus 0 SControl 300) Vendor: ATA Model: FUJITSU MHV2060B Rev: 0085 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 in you kernel configuration make sure under file system, nfs, root= nfs is unchecked.

They hope these examples will help you to get a better understanding of the Linux system and that you feel encouraged to try out things on your own.

To hotplug, in System/Preferences/Removal Drives and Media, Storage tab must be set to "mount removal drives when hot-plugged".

The important thing about these scripts is: they have to detach themselves.

There have been a lot of changes between 2.6.18 and 2.6.28, so saying no to all the changes will generate a kernel with most of the SATA support turned off. That would mean that the filesystem driver for your root partition is not in the kernel. I have it dual booting with Windows also (unfortunately, I need both).

Failure to use make oldconf will get you a kernel that is as mess, as the .config will not be legal for the new kernel. I assume that root is one of the partitions on /dev/sda ? Partition table: 1 = Dell Utility (don't know why I kept this) 2 = Windows 3 = /boot 4 = Extended 5 = swap 6 = / is taken directly from my working kernel boot, which is why I used that as a template for the 2.6.28 entry.

Search for gentoo driver sd needs updating:

gentoo driver sd needs updating-66gentoo driver sd needs updating-39

RTL-8139/8139C/8139C (rev 10)Linux version 2.6.30-ARCH ([email protected]) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Fri Jul 31 UTC 2009 SCSI subsystem initialized libata version 3.00 loaded.

Leave a Reply

Your email address will not be published. Required fields are marked *

One thought on “gentoo driver sd needs updating”